Abstract. On the basis of main provisions of ISO standards, reproducibility and repeatability in determination of measured characteristics of. Buy ISO ACCURACY (TRUENESS AND PRECISION) OF MEASUREMENT METHODS AND RESULTS – PART 6: USE IN PRACTICE OF. INTERNATIONAL STANDARD ISO ISO/TC 69, Applications of statistical methods, Subcommittee SC 6, Measurement methods.
|Published (Last):||28 April 2014|
|PDF File Size:||12.93 Mb|
|ePub File Size:||15.56 Mb|
|Price:||Free* [*Free Regsitration Required]|
NBN ISO 5725-6
Unless otherwise stated, a is assumed to be 0, Calibration-different Equipment-different Identifier for a particular laboratory Identifier for intermediate measures 57255-6 precision; in brackets, identification of the type of intermediate situation ldentif ier for a particular level IS0 Draft International Is adopted by the technical committees are circulated to the member bodies for voting. The differences are a there is an additional requirement to use an ac- cepted reference value, and b the number of participating laboratories and the number of test results shall also satisfy the re- quirements given 5752-6 4.
Al- though, for some measurement methods, the true value cannot be known exactly, 5725- may be possible to have an accepted reference value for the property being measured; for example, if suitable reference materials are available, or if the accepted reference value can be established by refer- ence to another measurement method or by preparation of a known sample.
It may appear that some laboratories did not use the required equipment or did not work ac- cording to the specified conditions. Take the smart route to manage medical device compliance.
In the latter case, it is necessary to investigate the causes of the discrep- ancy and possibly to ixo the experiment prior to proceeding further. In the former case, the repeatability standard devi- ation, gr, and the reproducibility standard deviation, gR, will be used for the assessment of the trueness of the measurement method. Utilisation dans la pratique des valeurs d’exactitude Title in German Genauigkeit Richtigkeit und Praezision von Messverfahren ixo Messergebnissen.
This implies comparison between the within-laboratory standard deviation and the stated repeatability standard deviation of the standard measurement method. The ISO Accuracy of Measurement Methods and Results Package provides the general principles necessary to accurately ieo measurement methods, results, applications and practical estimations.
Utilisation dans la pratique des valeurs d’exactitude. Trueness is normally expressed in terms of bias. If this is not true, the respective equations given in IS0 should be used to calculate s. As the voice of the U. Equations 8 to 10 oso sume an equal number n of test results in each laboratory.
572-56 more about the cookies we use and how to change your settings. In chemical anal- ysis, problems may 57725-6 from, for example, insufficient control of temperature, moisture, pres- ence of contaminants, etc.
Relevant International Standards on sample division should be consulted. The variation of the estimate of the bias of the measurement method is due to the variation in the results of the measurement process and is expressed by its standard deviation computed as in the case of known precision values, or siJzT-yF .
It is not applicable if the bias in the measurement of one property is affected by the level of a second property i. Unless otherwise stated, a is assumed to be 0. When a value for the bias of a measure- ment method is quoted, together with a test result obtained by that method, there is an implication that isk same characteristic is being measured in exactly the same way.
The units should be selected on a random basis for distribution.
ISO Accuracy of Measurement Methods and Results Package
Comparison of the trueness of two measurement methods is considered in IS0 Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. ISO matallic coatints measurement of coating thickness coulometic method by anodic dissolution.
Reference materials could be either a certified reference materials; b materials manufactured for the purpose of the experiment with known properties; or c materials whose properties have been established by measurements using an alternative measure- ment method whose bias is known to be negligi- ble. Need more than one copy? A Awar G 1, Please first log in with a verified email before subscribing to alerts. The symbols used in IS0 are given in annex A. 57256- results from each laboratory can be considered as replicates under repeatability conditions.
General principles and definitions – Part 2: The h and k values are shown in figures B. International 572-56, governmental and non-governmental, in liaison with ISO, also take part in the work.
Prior to conducting the as- sessment of trueness, a check of the io of the standard measurement method as applied by the lab- oratory shall be performed. All measurements are to be carried out according to that standard method.
The analytical results are listed in tableB. Use in practice of accuracy values. Basic methods for the determination of the trueness of a standard measurement method – Part 5: Laboratory means and laboratory variances Lab. If so, what are the improvements required? Click to learn jso. The faster, easier way to work with standards.
There are three cases, as follows. Here B is the laboratory component of bias, i. One laboratory re- sult was identified as a straggler; it originated from the same laboratory Lab.
IS0 l should be read in conjunction with all other parts of IS0including this part, because it gives the underlying definitions and general principles.
Enoval – References
Your Alert Profile lists the documents that will be monitored. Worldwide Standards We can source any standard from anywhere in the world. Anwendungen in der Praxis.