The Hicom E PBX system, the new family of systems with professional phone system for small and medium enterprises. The system supports ISDN and. responsibility for errors or omissions contained herein. Configuration Note – Ver C (03/01). Siemens Hicom E/E. & Office. Enhanced DTMF In-Band. Hicom E Hicom Hicom Hicom E Hicom Hicom Hicom Hicom , Hicom , Hicom , Hicom E. Hicom E OfficePoint.
|Published (Last):||21 October 2007|
|PDF File Size:||6.5 Mb|
|ePub File Size:||20.51 Mb|
|Price:||Free* [*Free Regsitration Required]|
An additional 5 allowed and barred number lists are available with up to ten 7-digit entries as of V2.
Call Group And Hunt Groups Got it, continue to print. As far as I remember it is a Hicom ?
Siemens Hicom E :: Briescom
Register now while it’s still free! Pin Assignment Of The V. Call keys virtual line keys Line seizure, automatic Via hicoj group and overflow trunk group Dial pause With analogue trunk programmable Project code Max.
Isdn Ddi Settings Defining The Call Interval By joining you are opting in to receive e-mail. After entering this password and resetting the system, the modules currently connected are recognized by the system.
Route Names Route 1: Hicom System Overview basic Box Dialling Into The Cn Initial Operation Plug the power hcom into the re-connected power supply.
Siemens HICOM 100E – 2
Page of Go. Confirm input Hhicom 2: Abbreviated dialling numbers can be sent after the network has been selected. Unrestricted trunk ac- User may telephone without any restrictions cess Table Classes of service as of SW 2. Voicemail group, for example, the box responds in the same way as it would for a direct station call retrieve messages from box.
Allocating Extensions And Actuators Actuator no. Press “F7” in the main menu to terminate remote administration. Defining Intercept, Incomplete Ddi Number Page Waiting times Ring attempts: Isdn Ddi Settings The required intercept console extensions are assigned to lines 1 to 4. Reset access code 6 characters: Querying hcom SW status of the system and the connected modules.
Siemens Hicom 100 E Manuals
Changing Port Configuration as of 2. The first call is then signalled as a camp-on call.
Do not remove jumpers unless expressly instructed to do so. Page 22 Do not allow readily flammable materials to hlcom stored near the installation or in the installation room. Outgoing Trunk Traffic Main Distribution Frame Hciom board connectors hicomm the terminal blocks. If a changed equipping scheme is detected during startup: Don’t show me this message again. With the default setting, the- se ext. Connecting Printer, Modem Or Pc Overview Of Modules Connecting Isdn Terminals Simply follow the user prompts; the system will always inform you of available and unavailable error messages options and will recommend corrective measures using expert mode branch address to collision entry found.
Upgrading A System Confirm input for list The classes of service correspond to the values specified in the chapter “Classes of service as of SW 2.
The signalling cycle is then increased to 10s intervals and the cyclical signals are maintained during the entire administration and maintenance procedure.
Behaviour In Emergencies Page Unrestricted trunk ac- User may telephone without any restrictions cess Table Classes of service as of SW 2. Normal Extensions 15 extensions can be a reference extension for any other Hicom E extension. Page – V. Page 81 Resetting a call Although a call is signalled, the called extension can seize another line without answering the first call.
Changing A Route In this type of network, at hkcom one free Hicom E analogue extension interface is hicoom to the trunk interface DTMF flash necessary of the satellite system.
The assignment is made in CDM 15 Suffix bicom of additional numbers is not restricted. Call forwarding in the exchange is only supported at extension 11 in the case of PMP.
CorNet port code 19 3