Life

ATMEGA328 TQFP PDF

The Atmel® picoPower® ATmega/P is a low-power CMOS 8-bit microcontroller 8-channel bit ADC in TQFP and QFN/MLF package. •. Temperature. Atmel high performance, low power 8-bit AVR ATmegaP-AU microcontroller in the TQFP package. Okay, so I’m about to blow up. I’ve tried to use perhaps 10 Atmega TQFP without any success.

Author: Goltill Maura
Country: Congo
Language: English (Spanish)
Genre: Relationship
Published (Last): 7 November 2008
Pages: 264
PDF File Size: 8.16 Mb
ePub File Size: 3.9 Mb
ISBN: 602-5-73074-815-9
Downloads: 81201
Price: Free* [*Free Regsitration Required]
Uploader: Sashakar

Assuming your connection is incorrect, first you need to add a aatmega328 resistor to the reset pin; 1kk should be alright. Any help would be appreciated.

Error while burning bootloader. If all that is correct, there are a couple other things that could cause that error: Block Poll Page Polled Memory Type Mode Delay Size Indx Paged Size Size Pages MinW MaxW ReadBack eeprom 65 20 4 0 no 4 0 0xff 0xff flash 65 6 0 yes 0xff 0xff lfuse 0 0 0 0 no 1 0 0 0x00 0x00 hfuse 0 0 0 0 no 1 0 0 0x00 0x00 efuse 0 0 0 0 atmega382 1 0 0 0x00 0x00 lock 0 0 0 0 no 1 0 tqfo 0x00 0x00 calibration 0 0 0 0 no atmwga328 0 0 0 0 0x00 0x00 signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00 Programmer Type: ATmegaP Chip Erase delay: If you have ever managed to program the fuses, the reset pin may have been disabled, tfp the device may be expecting an external crystal.

However, when attempting to upload the bootloader to the chip, I am presented with the following error:. Check that the ISP header connects to the pins that it ought to, and check that you have the chip oriented correctly in the socket The USBtiny has a switch to power the target, so make sure that’s in the correct position.

  EL CLAN DE LA LLOBA PDF

ATMega – TQFP – ktechnics

Only HV programming does not. It looks like the log text says ‘programmer operation not supported’, could be a symptom of tqf cmd line args. Ground yourself and use an ESD mat. The AVR programmer will not supply power. If this question can be reworded to fit the rules in the help centerplease edit the question.

Atmega 2 9 Clearly I’m doing something incorrectly, and I wouldn’t doubt if it was because it’s not as simple as hooking the AVR programmer directly up to the chip to program it. This question does not appear to be about electronics design hqfp the scope defined in the help center.

Crystal requirement comes when booting through the bootloader i.

ATmega328P Microcontroller – TQFP

It’s worth checking its in the correct position, though. Home Questions Tags Users Unanswered.

Tqcp you applied power to the circuit? Can you edit the question to include the exact command-line arguments given to avrdude? ISP requires a working clock source. By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. Well first of all, check the wiring. I’m voting to close this question as off-topic because it has been abandoned for half a year in unanswerable state.

  DURUFLE CHANT DONE PDF

If the reset pin has been disabled, you’ll need a special high voltage 12V programmer to recover it. Using SCK period of 10 usec avrdude: When programming through SPI, the chip accepts the program even if the fuses are set to accept clock signal from external clock. The reset pin lacks the normal ESD protection, and so is fairly easy to fry.

If all that is correct, there are tqcp couple other things that atmegaa328 cause that error:. Reset is driven by the programmer, and besides has an internal pullup.

Buy Products Online from China Wholesalers at

That is pretty much all you need. I’ve simply connected the AVR programmer to the chip in the adapter socket as follows AVR connector on left, chip on right. TomCarpenter, the programmer does provide power.

SCK serial program mode: