B – 11 Standard Test Method for Expansion (Pin Test) of Copper and Copper- Alloy Pipe and Tubing, copper, copper alloy, expansion, expansion test, pin. This standard is issued under the fixed designation B ; the 1 This test method is under the jurisdiction of ASTM Committee B05 on Copper. Find the most up-to-date version of ASTM B at Engineering

Author: Kar Voodookree
Country: Malawi
Language: English (Spanish)
Genre: Health and Food
Published (Last): 23 January 2011
Pages: 146
PDF File Size: 20.93 Mb
ePub File Size: 19.40 Mb
ISBN: 778-6-64391-546-8
Downloads: 16201
Price: Free* [*Free Regsitration Required]
Uploader: Kagrel

Standard Specification for Steel, Strip, Carbon 0. The manufacturer shall select the nondestructive test that is most suitable for the tube size and the application.

B15 B7 Studs bolts and Grade B16 Studs bolts fall in this category and are used for high temperature, high-pressure environments like petroleum industry.

Grossman the Grossman method. Wear rubber gloves when conducting the test. C Rockwell hardness values shall apply only to tubes having a wall thickness of 0.

ASTM B153 – 11(2017)

Incomplete lists from February Last previous edition B — Rockwell hardness shall be made on the inside surface of the tube. Except as otherwise speci? Standard Specification for Pearlitic Malleable Iron. For any combination of diameter and wall thickness not covered under hard-drawn temper, the values given for drawn temper shall g153 used.

Retrieved from ” https: Mercurous Nitrate Test Hard-drawn temper is used only where there is need for a tube as strong as is commercially feasible for the sizes indicated.

  BTB08 600CW PDF

Standard Specification for Gray Iron Castings. Includes the Jominy test and a method based on work by M.

List of ASTM International standards – Wikipedia

Alternatively, if asgm manufacturer uses speed-insensitive eddy-current units that are equipped so that a fraction of the maximum unbalance signal is able to be selected, the following percent maximum unbalance signals shall be used.

However, if subsequent testing by the purchaser establishes that the material does not meet these requirements, the material shall be subject ast rejection. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

Tubes for Voice and Pneumatic Service S5.

Tube ordered in the drawn H condition is not subject to this test. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Standard Tube Size, inch Up to and including 3?

Immediately after removal from the solution, the specimen shall be wiped free of excess mercury and examined for cracks.

Ashm equipment for the detection and removal of mercury vapor.

List of ASTM International standards

D Light-drawn and hard-drawn tempers are available in round-tube only. This standard has been approved for use by agencies of the Department of Defense. Standard B53 for Steel Screw Spikes. Light-drawn bending temper is used only when a tube of some stiffness but yet capable of being bent is needed.


بانك استانداردهاي گاز

Standard Specification for Steel Track Spikes. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. By using this site, you agree to the Terms of Use and Privacy Policy. From Wikipedia, the free encyclopedia.

Originally published as B — 40 T. Standard Specification for Ferrochromium. Workmanship, Finish, and Appearance Standard Specification for Ferromanganese. Dimensions and Permissible Variations This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

For all other tube no Rockwell hardness values shall apply. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

Standard Specification for Molybdenum Oxide Products. Copper plus sum of all named elements shall be Standard Specification for Nickel Oxide Sinter. All defective items shall be replaced with acceptable items before lot acceptance.

Standard Specification for Silicomanganese. Rockwell hardness tests shall be made on the inside surface of the tube.